全國咨詢熱線
一般情況下通過切片機成型的原料，相比其他粉碎型加工的原料，更能提高產品的檔次，同時設備穩定性好，操作方便。所以冷凝切片機在化工，制藥等行業被廣泛應用。在進行冷凝切片機的操作時一定要遵守操作程序，注意學習知識。
Generally, the raw materials formed by slicer can improve the grade of products compared with other crushed raw materials. At the same time, the equipment has good stability and convenient operation. Therefore, condensing slicer is widely used in chemical, pharmaceutical and other industries. When operating the condensing slicer, be sure to follow the operating procedures and pay attention to learning safety knowledge.
冷凝切片機是將加熱的液體原料，不銹鋼內冷卻轉輥在設備的料槽內轉動粘帶前部的可調節式切片刀裝置對其進行切片，從而使液體經冷卻刀片轉換為固體片料，亦可對液體經冷卻變?yōu)榻Y晶體的原料進行切片。
The condensing slicer is an adjustable slicer device that rotates the heated liquid raw material and the stainless steel internal cooling rotating roller in the material groove of the equipment to the front for slicing, so as to convert the liquid into solid sheet material through the cooling blade, and also slice the raw material from the liquid into crystal after cooling.
一、安裝及操作程序
1、 Installation and operation procedures
1、先檢查設備是否損壞，后安裝到位。注意保證滾筒的水平位置。
1. First check whether the equipment is damaged, and then install it in place. Pay attention to the horizontal position of the drum.
2、把輸送物料的管道與切片機的進口連接好，進料管道上順裝調節閥門。
2. Connect the pipeline conveying materials with the inlet of the slicer, and install the regulating valve on the feed pipeline.
3、把轉輥兩頭水冷卻接頭按進水和出水接好，熱媒加熱管與設備連接裝好。
3. Connect the water cooling joints at both ends of the rotating roller according to the inlet and outlet, and connect the heat medium heating pipe with the equipment.
4、開機檢查運轉是否正常，根據電柜指示，先按電源啟動按鈕，再打開變頻器調速有慢道快，觀察運轉是否正常。然后把切片刀和轉輥的間隙調好。
4. Start up and check whether the operation is normal. According to the instructions of the electric cabinet, first press the power start button, and then turn on the frequency converter. The speed regulation is slow and fast, and observe whether the operation is normal. Then adjust the gap between the slicer and the rotating roller.
5、接通冷卻水進料刀片，根據切片厚度調節進料的速度，檢查切片的厚度及其他要求能否達到要求。切片刀裝置順調和轉輥無間隙。
5. Connect the cooling water feeding blade, adjust the feeding speed according to the slice thickness, and check whether the slice thickness and other requirements can meet the requirements. The slicer device shall be smoothly adjusted to have no gap with the rotating roller.
6、一般正常物料凝固點在50度以上，可采用自來水冷卻，若凝固點低，需配置冷凍設備，冷卻越快，產量越高。
6. Generally, if the freezing point of normal materials is above 50 ℃, tap water can be used for cooling. If the freezing point is low, refrigeration equipment needs to be configured. The faster the cooling, the higher the output.
二、應注意事項
2、 Precautions
1、切片機電器部分必須進行接地。變頻器純虛比較復雜，請預先閱讀變頻器說明書，以防程序錯亂，造成不能使用。
1. The electrical part of the slicer must be grounded. The frequency converter is complex. Please read the manual of the frequency converter in advance to prevent the program from being disordered and making it unusable.
2、下料盆及下料口的地方屬高溫區，應避免接觸.
2. The place of the blanking basin and the blanking opening belongs to the high temperature area, and contact should be avoided
3、應注意下料盆物料凝固，萬一凝固，應關閉電源，把下料盆升溫之物料溶解為止，然后方可繼續生產。
3. Pay attention to the solidification of the materials in the blanking basin. In case of solidification, turn off the power supply and dissolve the materials heated in the blanking basin until they are dissolved, and then continue production.
4、渦輪減速機在生產之前應先加齒輪油。
4. Gear oil shall be added to the turbine reducer before production.
